Splitting humbucker coils

Humbuckers are essentially two single coils, side-by-side, wired in series (out of phase to "buck" the hum).  One cool feature is that you can split the coils and use them as true single coils to get a brighter, cleaner sound.  I say "split" the coils instead of "tap" the coils because that is something different entirely that gets confused often.  Coil "tapping" is having multiple leads going to the same coil to access different output values.  In order to "split" your coils, you must have four leads (five, including the bare ground wire).  Here are some common humbucker color codes:

By connecting the South finish (-) and North finish (+) you have both coils wired in series with South start (-) connected to ground and North start (+) connected to the volume lug or the switch.  The wiring diagram below shows how to wire my Apex Humbuckers to a switch like a push/pull potentiometer to switch between "single coil mode" and "humbucker mode".  You will notice that my color codes are the same as Lawrence and Gibson.

If you look at the Tele wiring diagram above you will see that when the tone control is pulled up the lower lugs are engaged and the finishes for the bridge pickup become the "hot" lead.  Ground stays at ground, that means the bridge South coil is engaged.  Simultaneously, the right side lugs connect the finishes for the neck pickup to ground, making them the negative lead.  Hot stays hot and you have the neck North coil engaged.  When the neck North and the Bridge south are used together (the middle switch position) they are hum-canceling because they are reverse polarity, wired in parallel, out of phase.  

On most humbuckers, the coil with the adjustable poles is South-up, you can check by using a compass.  The North needle will be attracted to the South-up pole and South will be attracted to North.  My Apex Humbuckers do not have adjustable poles, but North-up and South-up coils are labeled on the bottom or you can use a compass to check.  

You can have a lot of fun getting some different sounds out of your instrument just by wiring it differently.  One of my favorite websites for wiring diagrams is www.guitarelectronics.com.

How do humbuckers work?

Humbuckers are great for their warm, powerful tone, and best of all they "buck" the hum that single coils are usually are prone to.  60-cycle hum comes from electronics that surround us every day like florescent lights and power transformers, and it sure doesn't sound very good when it comes through an electric guitar amp.  That's why humbuckers were such a valuable invention when music was getting louder in the 1950's, but how do they work?

Humbuckers are basically two single coils arranged side-by-side (fig. 1), each with six magnetic poles or slugs (one for each string).  They are wired in a way that cancels the unwanted frequency and keeps as many of the good frequencies as possible.

fig. 1

Most modern Stratocaster guitars (fig. 2) have a humbucking option built in.  The middle pickup is reverse-wound/reverse-polarity to the neck and bridge, so that when they are used in combination they will cancel any hum.  This only works because the two coils are so far apart and the harmonic frequencies are so different, the only quality that is the same about them is the hum, so when the two coils are opposite, they cancel the hum. 

fig. 2 the middle and bridge or middle and neck pickups are hum-canceling together

 Humbuckers function a little differently than this. Since the coils are so close together (as close as they can possibly be without being on top of each other), they are sensing very similar sounds and they need to be out of phase to cancel the hum.  Humbuckers consist of two coils (both wound counter-clockwise) with opposite magnetic poles facing up, usually wired in series.  

Some people don't like how humbuckers aren't as clear or bright as single coils, but what a lot of people don't realize is that there are many different ways of building humbuckers to change the tone.  The original Seth Lover PAF humbucker (which is the baseline against which all other humbuckers are judged) consists of 5000 uniform winds per coil (not scatterwound), bar magnets mounted underneath, adjustable poles on one side, slugs on the other, topped off with a nickel-silver cover.  All of this makes for a pretty dark sounding pickup.  Which might sound great in certain guitars, but some guitars beg for bright, twangy tones.  You could use scatterwound coils (for a brighter, clearer sound) and solid Alnico polepieces much like a Strat pickup.  This is the formula I used for my Apex Humbuckers.

fig. 3 my Apex Humbucker

You could also have an underwound humbucker (say with 4000 winds per coil) for a brighter tone, and you could wire these coils in parallel (instead of in series) for pickup with a clear tone and absolutely no hum.  

So there are lots of different options when it comes to getting different tones out of humbuckers, they don't always have to be dark sounding.  Most modern humbuckers come with 4 conductor leads so you can split the coils, and you can look up a wiring diagram here to experiment a bit.  Knowing your color codes of your pickup wires will be very helpful too, here is a link to color codes of a number of popular humbucker manufacturers.